Rippa RS06 PRO: the tracked loader with load-sensing hydraulics
The Rippa RS06 PRO is a powerful skid loader on rubber tracks: 1,475 kg operating weight, 300 kg rated payload and 2.53 m lifting height. The load-sensing hydraulics supply up to 135 l/min, and the water-cooled Kubota D1105 three-cylinder engine delivers 22.9 hp. With two travel speeds up to 6.5 km/h and a standard quick coupler, the RS06 PRO is equipped for construction, landscaping and agriculture.
The RS06 PRO at a glance
- Loading and lifting: 300 kg rated payload, up to 600 kg payload, 2.53 m lifting height and 1.55 m dump height
- Tracked undercarriage: 230 mm wide rubber tracks with hydraulic track tensioning, 32.5 kPa ground pressure
- Engine: Kubota D1105 with 3 cylinders, water-cooled, 22.9 hp (17.1 kW), theoretical consumption of 1.3 to 1.5 l of diesel per hour
- Hydraulics: load-sensing control valve, main pump with 135 l/min, 22.5 MPa working pressure
- Travel: two travel speeds up to 6.5 km/h, 28% gradeability
- Equipment: quick coupler, armrest and counterweight as standard, bucket with 0.16 m³ and 1,150 mm width
You will find all technical data above under “Specifications”.
The RS06 PRO loads soil, gravel and bulk material, spreads material on site and loads trailers and skips with sides up to 1.55 m high. With pallet forks it stacks pallets, with the sweeper it cleans yards and roads, and with the 4-in-1 bucket it levels, grabs and loads with a single attachment. For demolition work there is a hydraulic breaker.
The 230 mm wide rubber tracks spread the weight over a large area, keeping the ground pressure at only 32.5 kPa. This lets the RS06 PRO make good progress even on soft ground, lawns and wet surfaces. The hydraulic track tensioning reliably keeps the tracks at the right tension.
The three-cylinder Kubota diesel delivers 22.9 hp at 3,000 rpm and is water-cooled. The load-sensing hydraulics adapt the flow to demand, so that travelling and working run smoothly at the same time. Spare parts for the engine and hydraulics can be found under spare parts for the RS06 PRO.
We offer a wide choice of attachments for the RS06 PRO, including buckets, a 4-in-1 bucket, pallet forks, a sweeper and a hydraulic breaker. Thanks to the standard quick coupler, you change them in a few minutes. All matching attachments can be found under attachments for the RS06 PRO.
The RS06 PRO has an open operator station with an armrest and stays low at a height of 1,472 mm. A cab is not available for this model. If you need a cab, you will find one as standard on the RS07.
We keep common spare and wear parts for the RS06 PRO in stock in Europe. Maintenance is easiest at your Rippa partner dealer – then it is documented straight away. In the Rippa Owners Club you register your machine and collect points for spare parts and maintenance.
Use “Request a quote” to receive a personal quote for the RS06 PRO, free of charge and without obligation. Alternatively, reserve it via Click & Collect for a 300 € deposit, which is credited in full against the purchase price. You collect it from a partner dealer near you and receive a briefing. Within the EU we deliver in 3–10 days, and the machine comes with a 24-month warranty from handover.
Do you need a smaller machine? Then take a look at the RS04. For a standard cab there is the RS07, and for 1,050 kg rated payload the RS20. You can compare all models under Rippa skid loaders and get personal advice via the contact form or on WhatsApp.
Matching attachments
These attachments fit your machine.